ASTM A962 DOWNLOAD

adminComment(0)

This standard is issued under the fixed designation A /A M; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. Home; ASTM A/AM $; Add to Cart. Printed Edition + PDF;; Immediate download; $; Add to Cart. ASTM AAM - - Designation: A/AM? 15 EDT 1 Downloaded/printed by Pontifcia Universidade Catlica do.


Astm A962 Download

Author:MIRANDA SCHARICH
Language:English, Dutch, German
Country:Belarus
Genre:Health & Fitness
Pages:545
Published (Last):14.03.2016
ISBN:804-8-34437-659-7
ePub File Size:16.41 MB
PDF File Size:12.50 MB
Distribution:Free* [*Registration needed]
Downloads:34676
Uploaded by: PEARLENE

ASTM A - 16a - Download as PDF File .pdf), Text File .txt) or read online. ASTM A - 16a. A/AM Specification for Common Requirements for 1 This specification is under the jurisdiction of ASTM Committee A01 on Downloaded/printed by. A/AM Specification for Common Requirements for 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel,. Stainless Steel and.

Chemical Composition product specification, and 7. Terminology A The chemical analysis methods—When bolting components have been produced by thus determined shall conform to the requirements of the forming, when they have been subjected to heat treatment, or individual product specification.

Product analysis check when the nominal thread size falls into a different diameter analysis tolerances shall not be applied to heat analysis range than that of the starting bar as shown in the applicable requirements. Impact tests are not required on material or from broken mechanical test specimens.

When multiple samples are taken from the same lot prescribed in the product specification. Hardness testing shall for product analysis, individual elements shall not vary both be performed in accordance with Test Methods and Definitions above and below the specified range. Steels with intentional additions of selenium may only be supplied or used when Tensile Requirements specifically called out in the product specification.

Mechanical Properties Methods and Definitions A Proof Load and Cone Proof Requirements tained from the production material, or, in the case of forgings, from separately forged test blanks prepared from the stock used Heat treatment shall be com- threaded mandrel or a test bolt as illustrated in Fig. Tension Method or b Compression Method. See Speci?

May also apply to work hardened condition or strength level, or both. Ordering Information 4.

Examples of such information include, but are not limited, to the following: 4. Box , Arlingate Ln.

ASTM A 962 - 16a

Melting Process 5. If secondary melting is employed, the heat shall be de? When steel of different grades is continuously cast identi?

The steel producer shall remove the transition material by an established procedure that positively separates the grades. Should the downloadr deem it necessary to have the transition zone of two heats of the same grade which are continuously cast discarded, the downloadr shall invoke Supplementary Requirement S Materials and Manufacture 6.

Finish hot or cold, ground, rough turned, drawn, etc.

Chemical Composition 7. If secondary melting processes are employed, the heat analysis shall be obtained from one remelted ingot or the product of one remelted ingot of each primary melt.

The chemical analysis thus determined shall conform to the requirements of the individual product speci? Product analysis check analysis tolerances shall not be applied to heat analysis requirements.

The chemical composition thus determined shall conform to the limits of the product speci? When multiple samples are taken from the same lot for product analysis individual elements shall not vary both above and below the speci? Steels with intentional additions of selenium may only be supplied or used when speci? Mechanical Properties 8. Heat treatment shall be completed prior to removal of material for mechanical testing.

List of ASTM International standards

Impact tests are not required on bars 1? Impact tests are not required on material from externally threaded fasteners when the thread diameter is 1?

Hardness Requirements 9.

Hardness testing shall be performed in accordance with Test Methods and De? Tensile Requirements Proof Load and Cone Proof Requirements The minimum proof load required by the product speci? The nut shall resist this load without stripping or rupture, and shall be removable by hand, without use of tooling, after the load is released. A wrench may be used to loosen the nut one-half turn maximum to start it in motion.

The test shall be discarded if the threads of the mandrel or test bolt are damaged during the test. The test uses a conical washer and threaded mandrel to determine the load-carrying ability of hardened steel nuts through 11?

AFNOR Editions Online Store

The FIG. The nut shall support its speci?

For sizes over 1? Impact Requirements The longitudinal axis of the specimen shall be parallel to the direction of rolling or, in the case of forgings, to the longest axis of the component the test bar represents.

The notch shall be located on the test specimen surface which most closely approaches a radial direction.

The base of the notch shall be as nearly as practicable perpendicular to the longest axis of the component. Workmanship, Finish, and Appearance The molten steel may be vacuum- tempering charge and submitted for inspection at the same treated prior to or during pouring of the ingot or strand casting.

If second- bolting components machined from the same lot of bolting ary melting is employed, the heat shall be defined as all of the material defined as outlined in either 3.

The steel process such as rolling, forging, or machining from the same producer shall remove the transition material by an established heat or cast of material, of the same prior condition, the same procedure that positively separates the grades. Should the size, and subjected to the same heat treatment in one tempering downloadr deem it necessary to have the transition zone of two charge. Ordering Information 6. Materials and Manufacture 4.

Finish hot needed material. Examples of such information include, but are rolled or cold drawn, rough turned, extruded, ground, or not limited, to the following: polished shall be at the option of the manufacturer unless 4.

Related titles

Chemical Composition product specification, and 7. Terminology A The chemical analysis methods—When bolting components have been produced by thus determined shall conform to the requirements of the forming, when they have been subjected to heat treatment, or individual product specification.

Product analysis check when the nominal thread size falls into a different diameter analysis tolerances shall not be applied to heat analysis range than that of the starting bar as shown in the applicable requirements. Impact tests are not required on material or from broken mechanical test specimens.Heat Treat Charts S All products are stringently checked upon arrival.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm. Bolting, which is composed of bolting materials, such as rods, bars, flats, and forgings, which are subsequently manufactured into bolting components, are a special sub-group of fasteners. Hardness testing shall for product analysis, individual elements shall not vary both be performed in accordance with Test Methods and Definitions above and below the specified range.

MAURITA from Olathe
Please check my other articles. I have a variety of hobbies, like streetball. I relish reading books coolly .
>