ISO 3269 PDF

adminComment(0)
    Contents:

Jun 1, ISO INTERNATIONAL. STANDARD. ISO. Third edition Details of the software products used to create this PDF file can be found. For sample test instructions during incoming goods inspections, ISO prescribes values for an "Acceptable Quality Level (AQL)" to which an acceptance. Jun 1, International Standard ISO was prepared by Technical Committee This second edition cancels and replaces the first edition (ISO


Iso 3269 Pdf

Author:ISELA DALPIAZ
Language:English, German, Dutch
Country:Mali
Genre:Health & Fitness
Pages:529
Published (Last):05.01.2016
ISBN:353-3-19845-586-9
ePub File Size:28.36 MB
PDF File Size:14.29 MB
Distribution:Free* [*Registration needed]
Downloads:41899
Uploaded by: KACI

Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible. This standard was last reviewed and confirmed in Therefore this version remains current. General information. Status: Published. Publication date: . ISO Sampling - Free download as Open Office file .odt), PDF File .pdf), Text File .txt) or read online for free.

Additional requirements for acceptance may be included in a specific product standard for example, one on prevailing torque-type nuts. The same procedure is also to be applied in cases where conformance to specification is disputed.

This International Standard is applicable to bolts, screws, studs, nuts, pins, washers, blind rivets and other related fasteners not intended for high volume machine assembly, special-purpose applications or specially engineered applications requiring greater in-process control and lot traceability see the note in the introduction.

The procedure for these products shall be agreed upon by the supplier and the downloadr prior to the confirmation of the order. This International Standard is applicable only to fully manufactured products; it neither implies nor includes any particular in-process control procedure or inspection during production. The production of accessories, services and partially fabricated parts for example, washers, nuts, plating, heat treatment and blanks for use in the manufacture of fasteners may be subcontracted to other suppliers by the fastener supplier.

Nevertheless, the supplier of the final, finished product shall be solely responsible for the fastener's quality.

The requirements of this International Standard apply only to the condition of fasteners at the time of delivery.

Customers Who Bought This Also Bought

Any process carried out after receipt for example, plating will invalidate the requirements of this International Standard. Annex B informative offers guidance to, and an explanation of, the principles upon which this International Standard is based.

Our policy towards the use of cookies Techstreet, a Clarivate Analytics brand, uses cookies to improve your online experience. They were placed on your computer when you launched this website.

Product grade C AQL 1.5 2.5 4

You can change your cookie settings through your browser. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below.

For undated references, the latest edition of the normative document referred to applies. Revision of ISO 2, To be published. Revision of ISO 3, To be published.

Symbols and designations of dimensions are defined in ISO I 5,46 6,48 8,56 10,58 12,7 16,7 20,64 1 min. I 22 -- 27,7.

I 4 5,3 6,4 7,5 10 12,5 k max. I 2,19 1 2,54 3,45 I 4,17 I 4,94 I 6,48 I 8. I 5,85 7,42 I 9,17 11,27 13,97 r min.

Related Post: BS EN ISO 9606 1 PDF

Requirements for non-electrolytically applied zinc flake coatings are covered in ISO If different electroplating requirements are desired or if requirements are needed for other finishes, they should be agreed between customer and supplier. Acceptability For acceptance procedure, see ISO S0 4 0 3 5 :1 9 9 9 , Hexagon thin nuts chamfered — Product grades A and B.

Other books: ISO 2 EBOOT V2

The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. Z Identical with ISO Bureau of Indian Standards BIS is a statutory institution established under the Bureau of Indian Standards Act, to promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country.

Copyright BIS has the copyright of all its publications. No part of these publications may be reproduced in any form without the prior permission in writing of BIS.More From scribd Javier Ricardo Romero Bohorquez.

Basker Venkataraman. Related titles. This Indian Standard has been developed from Doc : No. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designa- tions.

DORLA from San Francisco
Browse my other articles. One of my hobbies is yo-yoing. I am fond of exploring ePub and PDF books longingly .
>